mic69151/153 single supply v in , low v in , low v out , 1.5a ldo super ?ta pnp is a registered trademark of micrel, inc. micrel inc. ?2180 fortune drive ?san jose, ca 95131 ?usa ?tel +1 ( 408 ) 944-0800 ?fax + 1 (408) 474-1000 ?http://www.micrel.com december 2008 m9999-121908-c general description the mic69151/153 is the 1.5a output current member of the mic69xxx family of high current, low voltage regulators, which support currents of 1a, 1.5a, 3a, and 5a. the mic69151/153 operates from a single low voltage supply, yet offers high precision and ultra-low dropout of 500mv under worst case conditions. the mic69151/153 operates from an input voltage of 1.65v to 5.5v. it is designed to drive digital circuits requiring low voltage at high currents (i.e. plds, dsp, microcontroller, etc.). these regulators are available in adjustable and fixed output voltages including 1.8v. the adjustable version can support output voltages down to 0.5v. the cap design of the mic69151/153 is optimized for stability with low value low-esr ceramic output capacitors. features of the mic69151/153 include thermal shutdown and current limit protection. logic enable and error flag pins are also available. the mic69151/153 is offered in a tiny 10-pin 3mm x 3mm mlf package and an epad soic-8 package. both packages have an operating temperature range of ?0? to +125?. data sheets and support documentation can be found on micrel? web site at: www.micrel.com. features single input voltage range: v in : 1.65v to 5.5v maximum dropout (v in ?v out ) of 500mv over temperature adjustable output voltage down to 0.5v stable with 10f ceramic output capacitor excellent line and load regulation specifications logic controlled shutdown thermal shutdown and current limit protection 10-pin 3mm x 3mm mlf package epad soic-8 package available ?0? to +125? junction temperature applications point-of-load applications industrial power sensitive rf applications ___________________________________________________________________________________________________________ typical application fixed 1.8v regulator w/flag error adjustable regulator
micrel, inc. mic69151/153 december 2008 2 m9999-121908-c ordering information part number nominal output voltage junction temperature range package lead finish mic69151-1.8yml 1.8v ?0?to +125? 10-pin 3x3 mlf pb-free mic69151-1.8yme 1.8v ?0?to +125? 8-pin epad soic pb free mic69153yme adj. ?0?to +125? 8-pin epad soic pb free mic69153yml adj. ?0?to +125? 10-pin 3x3 mlf pb-free pin configuration nc en 5 1 flg nc gnd nc 10 adj/sns vout nc vin 9 8 7 2 3 4 6 1 gnd en vin vin 8 flg sns/adj vout vout 7 6 5 2 3 4 10-pin 3mm x 3mm mlf (ml) 8-pin epad soic (me) pin description pin number mlf-10 pin number epad soic-8 pin name pin function 1 8 flg error flag (output): open collector output. active low indicates an output fault condition. 2, 4, 5, 8 nc not internally connected. 3 (ep) 1 gnd ground (exposed pad is recommended to connect to ground on mlf ). 6 2 en enable (input): cmos compatible input. logic high = enable, logic low = shutdown. do not leave pin floating. 7 3, 4 vin input voltage which supplies current to the output power device. 9 5, 6 vout regulator output. 10 (adj) 7 (adj) adj adjustable regulator feedback input. connect to resistor voltage divider. 10 (fixed) 7 (fixed) sns sense pin, connect to output for improved voltage regulation.
micrel, inc. mic69151/153 december 2008 3 m9999-121908-c absolute maximum ratings (1) supply input voltage (v in ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6v logic input voltage (v en , v lq ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0v to v in power dissipation (p d ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . internally limited (3) flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6v storage temperature (t s ) . . . . . . . . . . . . . . . . . . . . . . . . . . . ?5? to +125? esd (4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2kv operating ratings (2) supply voltage (v in ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.65v to 5.5v enable input voltage (v en ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0v to v in junction temperature (t j ) . . . . . . . . . . . . . . . . . . . . ?0? t j +125? package thermal resistance 3x3 mlf (q ja ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60?/w epad soic-8 (q ja ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41?/w electrical characteristics (4) t a = 25? with v in = v out + 1v; bold values indicate ?0?< t j < +125?; i out = 10ma; c out 4.7f ceramic, unless otherwise noted. parameter conditions min typ max units output voltage accuracy (fixed) over temperature range ? +2 % output voltage accuracy (adj) 0.49 0.5 0.51 v feedback pin current 0.25 1 a output voltage line regulation (note 5) v in = v out +1.0v to 5.5v for v out 0.65v, v in = 1.65 to 5.5v ?.2 ?.3 %/v output voltage load regulation i l = 10ma to 1.5a ?.2 % v in ?v o ; dropout voltage (note 6) i l = 1.0a i l = 1.5a 185 250 300 500 mv mv ground pin current i l = 10ma i l = 0.5a i l = 1.5a 1.6 7.5 20 20 35 ma ma ma ground pin current in shutdown v en = 0v 1 a current limit v out = 0v 1.7 2.6 a start-up time v en = v in 10 150 s thermal shutdown 165 ? enable input enable input threshold regulator enable regulator shutdown 0.8 0.6 0.2 v v enable pin input current v il 0.2v (regulator shutdown) v ih 0.8v (regulator enable) 0.005 7 a a flag output i flg(leak) flag output leakage current (flag off) 0.05 a v flg(lo) output logic-low voltage (undervoltage condition), i l = 5ma 150 mv v flg threshold, % of v out below nominal (falling) 7.5 10 14 % hysteresis 2 % notes: 1. exceeding the absolute maximum rating may damage the device. 2. the device is not guaranteed to function outside its operating rating. 3. the maximum allowable power dissipation of any t a (ambient temperature) is (p d(max) = t j(max) ?t a ) / q ja . exceeding the maximum allowable power dissipation will result in excessive die temperature and the regulator will go into thermal shutdown. 4. specification for packaged product only. 5. minimum input for line regulation test is set to v out + 1v relative to the highest output voltage. 6. dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal value measured at 1v differential. for outputs below 1.65v, dropout voltage is considered the input-to-output voltage differential with the minimum input voltage of 1.65v. minimum input operating voltage is 1.65v.
micrel, inc. mic69151/153 december 2008 4 m9999-121908-c typical characteristics 0 10 20 30 40 50 60 70 power supply rejection ratio 1k 10k frequency (hz) v in = 3.3v v out = 1.8v i out = 0.5a 0 50 100 150 200 250 300 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 output current (a) 0 dropout voltage vs. output current v out = 1.8v c out = 10f 0 50 100 150 200 250 300 350 400 dropout voltage vs. temperature 20 40 60 80 temperature (?) v in = 3.3v v out = 1.8v i out =1.5a i out =750ma 0 2 4 6 8 10 12 14 16 18 ground current vs. output current 800 1200 output current (ma) v in = 3v v out = 1.8v c out = 10f 0 2 4 6 8 10 12 14 16 ground current vs. temperature 20 40 60 80 temperature (?) v in = v out +1 v out = 1.8v c out = 10f 1a 0.5a 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0 0.5 1.0 1.5 2.0 2.5 3.0 input voltage (v) output voltage vs. input voltage v out = 1.8v c out = 10f 1a 750ma 1.70 1.72 1.74 1.76 1.78 1.80 1.82 1.84 1.86 1.88 1.90 output voltage vs. temperature 20 40 60 80 temperature (?) v in = 3.3v v out = 1.8v i out = 10ma 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 current limit vs. temperature 20 40 60 80 temperature (?) v in = 3.3v v out = 1.8v 1.786 1.788 1.790 1.792 1.794 1.796 1.798 1.800 1.802 0 0.25 0.5 0.75 1.0 1.25 1.5 output current (a) load regulation v in = 3v v out = 1.8v c out = 10f 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 enable threshold vs. temperature 20 40 60 80 temperature (?) v in = 2.8v v out = 1.8v c out = 10f i out = 100ma on off
micrel, inc. mic69151/153 december 2008 5 m9999-121908-c functional characteristics
micrel, inc. mic69151/153 december 2008 6 m9999-121908-c functional diagram enable in en out adj v ref gnd v ref 50mv flg
micrel, inc. mic69151/153 december 2008 7 m9999-121908-c application information the mic69151/153 is an ultra-high performance low dropout linear regulator designed for high current applications requiring a fast transient response. it utilizes a single input supply, perfect for low-voltage dc-to-dc conversion. the mic69151/153 requires a minimum number of external components. the mic69151/153 regulator is fully protected from damage due to fault conditions offering constant current limiting and thermal shutdown. input supply voltage v in provides high current to the collector of the pass transistor. the minimum input voltage is 1.65v allowing conversion from low voltage supplies. output capacitor the mic69151/153 requires a minimum of output capacitance to maintain stability. however, proper capacitor selection is important to ensure desired transient response. the mic69151/153 is specifically designed to be stable with low esr ceramic chip capacitors. a 10f ceramic chip capacitor should satisfy most applications. output capacitor can be increased without bound. see typical characteristics for examples of load transient response. x7r dielectric ceramic capacitors are recommended because of their temperature performance. x7r-type capacitors change capacitance by only 15% over their operating temperature range and are the most stable type of ceramic capacitors. z5u and y5v dielectric capacitors change value by as much as 50% and 60%, respectively over their operating temperature ranges. to use a ceramic chip capacitor with y5v dielectric the value must be much higher than an x7r ceramic or a tantalum capacitor to ensure the same capacitance value over the operating temperature range. tantalum capacitors have a very stable dielectric (10% over their operating temperature range) and can also be used with this device. input capacitor an input capacitor of 1f or greater is recommended when the device is more than 4 inches away from the bulk supply capacitance or when the supply is a battery. small, surface mount, ceramic chip capacitors can be used for the bypassing. the capacitor should be placed within 1 inch of the device for optimal performance. larger values will help to improve ripple rejection by bypassing the input to the regulator further improving the integrity of the output voltage. minimum load current the mic69151/153 regulator is specified between finite loads. if the output current is too small, leakage currents dominate and the output voltage rises. a 10ma minimum load current is necessary for proper operation. adjustable regulator design the mic69153 adjustable version allows programming the output voltage anywhere between 0.5v and 5.5v with two resistors. the resistor value between v out and the adjust pin should not exceed 10k?. larger values can cause instability. the resistor values are calculated by: ? + * = 1 r r 0.5 v 2 1 out where v out is the desired output voltage. enable the fixed output voltage versions of the mic69151 feature an active high enable input (en) that allows on- off control of the regulator. current drain reduces to near ?ero? when the device is shutdown, with only microamperes of leakage current. en may be directly tied to v in and pulled up to the maximum supply voltage. thermal design linear regulators are simple to use. the most complicated design parameters to consider are thermal characteristics. thermal design requires the following application-specific parameters: maximum ambient temperature (t a ) output current (i out ) output voltage (v out ) input voltage (v in ) ground current (i gnd ) first, calculate the power dissipation of the regulator from these numbers and the device parameters from this data sheet. p d = (v in ?v out ) i out + v in i gnd where the ground current is approximated by using numbers from the ?lectrical characteristics? or ?ypical characteristics? sections. the maximum allowable power dissipation of any t a (ambient temperature) is p d(max) = (t j(max) ? t a ) / q ja . exceeding the maximum allowable power dissipation will result in excessive die temperature and the regulator will go into thermal shutdown. refer to ?pplication note 9? for further details and examples on thermal design and heat sink applications.
micrel, inc. mic69151/153 december 2008 8 m9999-121908-c package information 10-pin 3mm x 3mm mlf (ml) 8-pin epad soic (me)
micrel, inc. mic69151/153 december 2008 9 m9999-121908-c micrel, inc. 2180 fortune drive san jose, ca 95131 usa tel +1 (408) 944-0800 fax +1 (408) 474-1000 web http://www.micrel.com the information furnished by micrel in this data sheet is believed to be accurate and reliable. however, no responsibility is assumed by micrel for its use. micrel reserves the right to change circuitry and specifications at any time without notification to the customer. micrel products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. a purchaser? use or sale of micrel products for use in life support appliances, devices or systems is a purchaser? own risk and purchaser agrees to fully indemnify micrel for any damages resulting from such use or sale. ?2008 micrel, incorporated.
|
